Technical12 Aug 2026
Why manganese jaw plates fail early
Carbide networks, late quenching and heavy sections — the three things that stop manganese steel doing its one job.
Read
Home / News
News & insight
Technical notes from the shop floor, where to find us this year, and what we have been posting on LinkedIn.
Solution annealing — the 45-second windowFeatured · Technical12 August 20266 min
Why manganese jaw plates fail at 60% of expected life
Work hardening only helps if the casting reaches you fully austenitic.
Most premature manganese failures are not caused by the ore. They are caused by carbide networks left in the structure because the soak was short, the quench was late, or the section was too heavy for the cycle used. This piece walks through what to look for on a micrograph, and what to ask your supplier for.
Blog
Written by our metallurgy and quality teams.
Articles below are illustrative placeholders. Replace with your own posts.
Quality28 Jul 2026
Reading a heat treatment chart like an auditor
Soak time, ramp rate and the quench window. What a good chart shows and the patterns that should prompt a question.
Read
Procurement14 Jul 2026
Cost per tonne crushed beats cost per casting
A cheaper wear part that lasts 40% less is not cheaper. Comparing quotations on the number that actually matters.
Read
Technical30 Jun 2026
No-bake versus green sand for heavy wear castings
Why we moved the whole line to two-part finotech resin sand in 2011, and what it did to scatter and rejection.
Read
Sustainability18 Jun 2026
What 820 kWp of rooftop solar actually changed
Eighteen months of generation data against plant load, and an honest look at what solar can do for induction melting.
Read
People02 Jun 2026
From ITI apprentice to shift in-charge in nine years
Kiran Rathod on what the ladder looks like from the bottom rung, and what he would tell a nineteen-year-old today.
Read
Events
Where to find us.
Book a slot with our engineering team in advance and we will have your drawings reviewed before you reach the stand.
14Sep
Cement Expo India 2026, Ahmedabad
Hall 2, Stand B-44. Mill liners, kiln and cooler grate plates, and the heat-resistant grade range.
14–16 September 2026Exhibiting21Oct
IIF Regional Convention, Vadodara
Our Head of Metallurgy presents on solidification modelling for heavy manganese sections.
21 October 2026Speaking03Dec
Open house, GIDC Savli works
A guided walk-through of melting, moulding, heat treatment and the laboratory. Limited to 25 visitors.
3 December 2026Registration required11Feb
IFEX 2027, Hall 3, Stand C-18
Showing the 10 MT single-piece capability and the finish-machining cell, with the full crusher wear range.
11–13 February 2027Exhibiting
From LinkedIn
Latest posts.
Follow the company page for plant updates, hiring news and technical notes.
Baroda Hi-Tech Alloys Pvt. Ltd.3d · Vadodara, Gujarat
Our first 9.4 MT single-piece mill liner came out of the 15 MT annealing furnace this week. Poured from one heat on the 3,500 KW furnace, quenched in 41 seconds. Good work from the melting and heat treatment teams. #casting #manganesesteel #foundry
184 reactions · 21 commentsView
Baroda Hi-Tech Alloys Pvt. Ltd.1w · Vadodara, Gujarat
Batch 14 of the Kaushal pre-apprenticeship programme graduated on Saturday. Thirty-two young people from Manjusar and nearby villages, eleven of them women. Nine have accepted apprenticeships with us. #CSR #skilling #MSME
312 reactions · 44 commentsView
Baroda Hi-Tech Alloys Pvt. Ltd.2w · Vadodara, Gujarat
Hiring: Shift In-charge (Melting), Quality Engineer (NDT) and a Methoding Engineer. If you have run an induction melting shift or interpreted a radiograph on a heavy section, we would like to talk. #hiring #metallurgy
96 reactions · 8 commentsOpen roles
Baroda Hi-Tech Alloys Pvt. Ltd.3w · Vadodara, Gujarat
ZED Gold re-assessment cleared with no non-conformities. Thanks to the QCI assessment team, and to everyone who kept the 5S discipline going when nobody was auditing. #ZED #qualitycouncilofindia
221 reactions · 17 commentsCertifications
Connecting the live feed
These cards are static placeholders. To pull real posts, connect the LinkedIn Pages API or a feed widget such as Taggbox, Juicer or EmbedSocial and render into this container. The markup is already structured for it.
Stay in touch
One email a quarter.
Technical notes, capacity updates and where we will be exhibiting. Unsubscribe in one click. We do not share the list.